Световой меч для саберфайтинга и дуэлей купить - Warsabers

Комплект электроники “Оптимум”

Warsabers — Mon, 16 May 2022 11:44:09 +0000

Сменный комплект электроники "Оптимум" для световых мечей в составе:

Pogo-pin коннектор для светодиодного клинка;
Звуковая карта начального уровня с несколькими различными наборами звуковых эффектов: включение, выключение, взмахи, удары, отбивание бластера, скрещивание мечей;
Аккумулятор ёмкостью 3000 мАч;
Кнопка;
Разъем для зарядки;
Динамик.

The post Комплект электроники “Оптимум” appeared first on Warsabers.

Duelling Kit

Warsabers — Tue, 24 Aug 2021 17:05:07 +0000

Completed with standard empty blade (92 cm long, 2 mm wall thickness) and a Tri-Cree LED converter module, which is installed by default in to blade holder.

The post Duelling Kit appeared first on Warsabers.

Revanted hilt

Warsabers — Fri, 09 Oct 2020 09:28:40 +0000

Design and development of hilt - Warsabers & ShtokCustomWorx Russia;

Design and development of crystal chamber - ShtokCustomWorx Russia;

Hilt size:

Length - 265 mm;
OD - 30-39 mm.

Dimensions for electronics:

Length - 117 mm;
ID - 28 mm.

Additional space for electronics:

Length - 25 mm;
ID - 25 mm.

Equipment:

Empty hilt- 1 pcs;
Brass buttons - 2 pcs;
Cooper buttons - 2 pcs;
Brass covertec wheel - 1 pcs;
Black aluminium covertec wheel - 1 pcs;
Copper emitter - 1 pcs;
Brass emitter - 1 pcs;
Button PCB - 2 pcs;
Heatsink LED module - 1 pcs.

NOT included:

NeoPixel connector;
Belt clip;
Blade;
Crystal chamber.

The post Revanted hilt appeared first on Warsabers.

1″ Heavy grade polycarbonate Blade

Warsabers — Wed, 12 Aug 2020 11:55:10 +0000

The post 1″ Heavy grade polycarbonate Blade appeared first on Warsabers.

Soundboards CerbeRUS Core

Warsabers — Tue, 28 Apr 2020 16:14:18 +0000

- Size - 22x70x6,5mm;
- LED - 3 FULL mixing LED DRIVER, 1.25A per chanel;
- Power supply - 3-5V;
- Sound - 16bit, 16 - 96 kHz/sec, class D speaker driver;
- Memory - microSD card (FAT32).

The post Soundboards CerbeRUS Core appeared first on Warsabers.

1″ Polycarbonate Blade

Warsabers — Mon, 20 Jan 2020 14:53:27 +0000

The post 1″ Polycarbonate Blade appeared first on Warsabers.

PixelBlade RGB

Warsabers — Wed, 24 Jul 2019 09:52:21 +0000

Material - impact resistant polycarbonate;
Length- 92 cm;
Wall thickness - 3 mm;
RGB LED stripe inside.

The post PixelBlade RGB appeared first on Warsabers.

Lightsaber stand

Warsabers — Thu, 04 Jul 2019 14:58:19 +0000

The post Lightsaber stand appeared first on Warsabers.

Starkiller V4 hilt

Warsabers — Thu, 10 Jan 2019 17:35:23 +0000

Hilt size:

Length - 285 mm;
OD - 38 mm.

Dimensions for chassis space:

Length - 122 mm;
ID - 30 mm.

Equipment:

Empty hilt - 1 pcs;
Emitter type 2 - 1 pcs;
PCB for hilt assembly and electronic install - 3 pcs;
Rubber fixer for button box PCB- 1 psc;
Crystal – 1 pcs.

NOT included:

Hex screws not included! Required 2mm and 1,5mm hex keys!

The post Starkiller V4 hilt appeared first on Warsabers.

Coupler staff

Warsabers — Wed, 18 Jul 2018 19:55:04 +0000

https://www.youtube.com/watch?v=5-72t7bE7ko

For hilts:

Warder
Destiny
Eternal
Paladin
Revenge

The post Coupler staff appeared first on Warsabers.

Blade Scabbard

Warsabers — Wed, 01 Feb 2023 19:43:51 +0000

For blade D=25,4 мм.

The post Blade Scabbard appeared first on Warsabers.

Kyle Katarn

Warsabers — Wed, 06 Oct 2021 14:06:27 +0000

HiltElectronicsBlade

The most accurate copy of the lightsaber Kyle Katarn – the main character of the game “Star Wars Jedi Knight”.
Design – Warsabers in coloboration with Maksim Tsvetkov, Russia;
Manufacturing – Warsabers, Russia;
Lenght: 320 mm;
OD: 38 мм;
Blade landing depth (aprox) – 35 mm/20 mm (Neopixel/NeoCree);
Blade retention screw – M4, 1 pcs. Hex key included;
Hilt is designed for hard dueling;

The photo may differ slightly from the finished product, due to manual processing of the product and the peculiarities of color transfer by the camera and screen

Video reviews of various hilts

Warsabers NeoCore Soundboard (Russia) with Smoothswings algorithm support:

4 built-in sound profiles. Ability to add new profiles and sounds. You can buy and download additional sound profiles at saberfont.com;
Smoothswing’s advanced motion recognition technology continuously generates sword swing / movement sounds in real time based on the intensity of the swing / movement;
18 different types of lightsaber sound effects: on, off, smooth swing (2 types), strong swing, background hum of work, hit, blaster hitting, clinch, force, combo, acceleration, stab, profile switch, profile name, background music, the sound of the transition of the lightsaber from sleep mode to ready mode;
10 system sounds: connecting a charger, volume levels (4 pcs.), switching sound and color profiles, menu background sound, entering the settings menu, saving settings;
24 color blade profiles (various colors, styles, effects). Blade lighting effects: smooth advance / retraction of the blade, flashes in random places of the blade when hitting / bouncing the blaster, blade flickering, clinch effect. The ability to customize each profile or effect, as well as add new profiles;
40 adjustable basic lightsaber settings, such as volume, sensitivity of swing, strike, stab, etc. The settings are made using the SettingsEdditor.exe program (on the SD card) or manually in the settings files;
41 customization of blade color profiles. You can read more about the profile settings in the instructions for the NeoCore soundboard;
Indication of the battery charge level in standby mode by means of the color and length of the blade at the base (from red to green);
Built-in protection of the battery against overcharge, overdischarge and short circuit;
“Sleep mode” which automatically cuts off power consumption when not using the lightsaber for more than 5 minutes. This mode will save the battery power for a long time;
Built-in controller of charging from USB sources;
Removable SD card, which can be accessed by connecting the sword through the micro-USB connector to a PC. Customization of the lightsaber is done directly on the SD card.

For PixelBlade RGB equipment: 1″, 92 cm long blade, 3 mm wall thickness and a bullet tip. RGB LED strips are installed inside the blade along the entire length and allow you to customize any blade color. This version is suitable for most users, because includes better lighting effects and the highest brightness of the blade. For hard dueling the PixelBlade RGB imposes certain restrictions, because the cost of replacing the blade in case of breakage is quite high.It is possible to independently install a special converter module with Tri-Cree LEDs in to blade holder to use standard empty blades (blade and converter module are purchase separately);

For duelling kit equipment: standard 1″ empty blade (92 cm long, 2 mm wall thickness). Powerful Tre-Cree RGB LED are installed at the blade holder and allow you to customize any blade color. This version is suitable for users who plan to use a lightsaber in the hard dueling conditions with heavy loads on the blade and the probability of damaging or breaking the blade – the cost of replacing the blade is not high. Light effects are applied to the entire blade at once because only one powerful Tri-Cree LED is used at the base. The brightness of the blade is less than that of the PixelBlade RGB, but the operating time from one battery charge increases. It is possible to install the PixelBlade RGB (purchased separately). For installation need to remove the converter module from the blade holder.

The post Kyle Katarn appeared first on Warsabers.

Starkiller

Warsabers — Tue, 14 Sep 2021 11:57:13 +0000

HiltElectronicsBlade

The most accurate copy of Galen Marek (Starkiller) lightsaber – the main character of the the game “Star Wars: The Force Unleashed”.

Design – Warsabers, Russia;
Lenght: 285 mm;
OD: 38 мм;
Blade landing depth (aprox) – 44 mm/29 mm (Neopixel/NeoCree);
Blade retention screw – M4, 1 pcs. Hex key included;
Сovertech wheel included. Covertech belt clip selling separately;
Hilt is designed for hard dueling;

The photo may differ slightly from the finished product, due to manual processing of the product and the peculiarities of color transfer by the camera and screen

Video reviews of various hilts

Warsabers NeoCore Soundboard (Russia) with Smoothswings algorithm support:

4 built-in sound profiles. Ability to add new profiles and sounds. You can buy and download additional sound profiles at saberfont.com;
Smoothswing’s advanced motion recognition technology continuously generates sword swing / movement sounds in real time based on the intensity of the swing / movement;
18 different types of lightsaber sound effects: on, off, smooth swing (2 types), strong swing, background hum of work, hit, blaster hitting, clinch, force, combo, acceleration, stab, profile switch, profile name, background music, the sound of the transition of the lightsaber from sleep mode to ready mode;
10 system sounds: connecting a charger, volume levels (4 pcs.), switching sound and color profiles, menu background sound, entering the settings menu, saving settings;
24 color blade profiles (various colors, styles, effects). Blade lighting effects: smooth advance / retraction of the blade, flashes in random places of the blade when hitting / bouncing the blaster, blade flickering, clinch effect. The ability to customize each profile or effect, as well as add new profiles;
40 adjustable basic lightsaber settings, such as volume, sensitivity of swing, strike, stab, etc. The settings are made using the SettingsEdditor.exe program (on the SD card) or manually in the settings files;
41 customization of blade color profiles. You can read more about the profile settings in the instructions for the NeoCore soundboard;
Indication of the battery charge level in standby mode by means of the color and length of the blade at the base (from red to green);
Built-in protection of the battery against overcharge, overdischarge and short circuit;
“Sleep mode” which automatically cuts off power consumption when not using the lightsaber for more than 5 minutes. This mode will save the battery power for a long time;
Built-in controller of charging from USB sources;
Removable SD card, which can be accessed by connecting the sword through the micro-USB connector to a PC. Customization of the lightsaber is done directly on the SD card.

For PixelBlade RGB equipment: 1″, 92 cm long blade, 3 mm wall thickness and a bullet tip. RGB LED strips are installed inside the blade along the entire length and allow you to customize any blade color. This version is suitable for most users, because includes better lighting effects and the highest brightness of the blade. For hard dueling the PixelBlade RGB imposes certain restrictions, because the cost of replacing the blade in case of breakage is quite high.It is possible to independently install a special converter module with Tri-Cree LEDs in to blade holder to use standard empty blades (blade and converter module are purchase separately);

For duelling kit equipment: standard 1″ empty blade (92 cm long, 2 mm wall thickness). Powerful Tre-Cree RGB LED are installed at the blade holder and allow you to customize any blade color. This version is suitable for users who plan to use a lightsaber in the hard dueling conditions with heavy loads on the blade and the probability of damaging or breaking the blade – the cost of replacing the blade is not high. Light effects are applied to the entire blade at once because only one powerful Tri-Cree LED is used at the base. The brightness of the blade is less than that of the PixelBlade RGB, but the operating time from one battery charge increases. It is possible to install the PixelBlade RGB (purchased separately). For installation need to remove the converter module from the blade holder.

The post Starkiller appeared first on Warsabers.

Inquisitor

Warsabers — Tue, 07 Sep 2021 15:19:14 +0000

HiltElectronicsBlade

Design – Warsabers, Russia;
The ability to combine two lightsabers into a staff using a special connector (selling separately);
Lenght: 299 mm;
OD: 36-40 мм.
Blade depth (aprox) – 56 mm/39 mm (PixelBlade/Tri-CREE);
Blade retention screw – M4, 1 pcs. Hex key included;
Сovertech wheel included. Covertech belt clip selling separately;
Hilt is designed for hard dueling.

The photo may differ slightly from the finished product, due to manual processing of the product and the peculiarities of color transfer by the camera and screen

Video reviews of various hilts

Warsabers NeoCore Soundboard (Russia) with Smoothswings algorithm support:

4 built-in sound profiles. Ability to add new profiles and sounds. You can buy and download additional sound profiles at saberfont.com;
Smoothswing’s advanced motion recognition technology continuously generates sword swing / movement sounds in real time based on the intensity of the swing / movement;
18 different types of lightsaber sound effects: on, off, smooth swing (2 types), strong swing, background hum of work, hit, blaster hitting, clinch, force, combo, acceleration, stab, profile switch, profile name, background music, the sound of the transition of the lightsaber from sleep mode to ready mode;
10 system sounds: connecting a charger, volume levels (4 pcs.), switching sound and color profiles, menu background sound, entering the settings menu, saving settings;
24 color blade profiles (various colors, styles, effects). Blade lighting effects: smooth advance / retraction of the blade, flashes in random places of the blade when hitting / bouncing the blaster, blade flickering, clinch effect. The ability to customize each profile or effect, as well as add new profiles;
40 adjustable basic lightsaber settings, such as volume, sensitivity of swing, strike, stab, etc. The settings are made using the SettingsEdditor.exe program (on the SD card) or manually in the settings files;
41 customization of blade color profiles. You can read more about the profile settings in the instructions for the NeoCore soundboard;
Indication of the battery charge level in standby mode by means of the color and length of the blade at the base (from red to green);
Built-in protection of the battery against overcharge, overdischarge and short circuit;
Built-in controller of charging from USB sources;
Removable SD card, which can be accessed by connecting the sword through the micro-USB connector to a PC. Customization of the lightsaber is done directly on the SD card.

For PixelBlade RGB equipment: 1″, 92 cm long blade, 3 mm wall thickness and a bullet tip. RGB LED strips are installed inside the blade along the entire length and allow you to customize any blade color. This version is suitable for most users, because includes better lighting effects and the highest brightness of the blade. For hard dueling the PixelBlade RGB imposes certain restrictions, because the cost of replacing the blade in case of breakage is quite high.It is possible to independently install a special converter module with Tri-Cree LEDs in to blade holder to use standard empty blades (blade and converter module are purchase separately);

For duelling kit equipment: standard 1″ empty blade (92 cm long, 2 mm wall thickness). Powerful Tre-Cree RGB LED are installed at the blade holder and allow you to customize any blade color. This version is suitable for users who plan to use a lightsaber in the hard dueling conditions with heavy loads on the blade and the probability of damaging or breaking the blade – the cost of replacing the blade is not high. Light effects are applied to the entire blade at once because only one powerful Tri-Cree LED is used at the base. The brightness of the blade is less than that of the PixelBlade RGB, but the operating time from one battery charge increases. It is possible to install the PixelBlade RGB (purchased separately). For installation need to remove the converter module from the blade holder.

The post Inquisitor appeared first on Warsabers.

Destiny

Warsabers — Mon, 23 Aug 2021 07:37:09 +0000

HiltElectronicsBlade

Design – Warsabers, Russia;
Lenght: 295 mm;
OD: 28-38 mm;
Blade depth (aprox) – 70/55 mm (Neopixel/NeoCree converter module);
Blade retention screw – M4, 1 pcs.;
Leather not installed. Leather stripe is included for self-installation;
The ability to combine two lightsabers into a staff using a special connector (selling separately);
Сovertech wheel and belt clip selling separately;
Hilt is designed for hard dueling.

The photo may differ slightly from the finished product, due to manual processing of the product and the peculiarities of color transfer by the camera and screen

Video reviews of various hilts

Warsabers NeoCore Soundboard (Russia) with Smoothswings algorithm support:

4 built-in sound profiles. Ability to add new profiles and sounds. You can buy and download additional sound profiles at saberfont.com;
Smoothswing’s advanced motion recognition technology continuously generates sword swing / movement sounds in real time based on the intensity of the swing / movement;
18 different types of lightsaber sound effects: on, off, smooth swing (2 types), strong swing, background hum of work, hit, blaster hitting, clinch, force, combo, acceleration, stab, profile switch, profile name, background music, the sound of the transition of the lightsaber from sleep mode to ready mode;
10 system sounds: connecting a charger, volume levels (4 pcs.), switching sound and color profiles, menu background sound, entering the settings menu, saving settings;
24 color blade profiles (various colors, styles, effects). Blade lighting effects: smooth advance / retraction of the blade, flashes in random places of the blade when hitting / bouncing the blaster, blade flickering, clinch effect. The ability to customize each profile or effect, as well as add new profiles;
40 adjustable basic lightsaber settings, such as volume, sensitivity of swing, strike, stab, etc. The settings are made using the SettingsEdditor.exe program (on the SD card) or manually in the settings files;
41 customization of blade color profiles. You can read more about the profile settings in the instructions for the NeoCore soundboard;
Indication of the battery charge level in standby mode by means of the color and length of the blade at the base (from red to green);
Built-in protection of the battery against overcharge, overdischarge and short circuit;
Built-in controller of charging from USB sources;
Removable SD card, which can be accessed by connecting the sword through the micro-USB connector to a PC. Customization of the lightsaber is done directly on the SD card.

For PixelBlade RGB equipment: 1″, 92 cm long blade, 3 mm wall thickness and a bullet tip. RGB LED strips are installed inside the blade along the entire length and allow you to customize any blade color. This version is suitable for most users, because includes better lighting effects and the highest brightness of the blade. For hard dueling the PixelBlade RGB imposes certain restrictions, because the cost of replacing the blade in case of breakage is quite high.It is possible to independently install a special converter module with Tri-Cree LEDs in to blade holder to use standard empty blades (blade and converter module are purchase separately);

For duelling kit equipment: standard 1″ empty blade (92 cm long, 2 mm wall thickness). Powerful Tre-Cree RGB LED are installed at the blade holder and allow you to customize any blade color. This version is suitable for users who plan to use a lightsaber in the hard dueling conditions with heavy loads on the blade and the probability of damaging or breaking the blade – the cost of replacing the blade is not high. Light effects are applied to the entire blade at once because only one powerful Tri-Cree LED is used at the base. The brightness of the blade is less than that of the PixelBlade RGB, but the operating time from one battery charge increases. It is possible to install the PixelBlade RGB (purchased separately). For installation need to remove the converter module from the blade holder.

The post Destiny appeared first on Warsabers.

NeoCree conversion module

Warsabers — Mon, 17 May 2021 13:59:17 +0000

These have been designed and produced by Warsabers and ShtokCustomWorx to conveniently allow users to seamlessly convert their neopixel lightsaber builds, that use pogo pin PCB connectors, to an RGB ‘in-hilt’ LED system.

Note. This is for use with 1” thin walled blades that must have a 7/8” ID (22.22mm).

Features:

Large copper heat sink for efficient High Power LED cooling
Built-in 55 kOhm “Blade ID” resistor between Data and GND
Brightest binned Cree XP-E2 LEDs
PCB compatible with TCSS/SCW/KR PCB's
SinkPad II copper core MCPCB
Each of 3 LED channels are configured to drive connected LEDs at around 1000mA
Module can be custom modified to any colour combination by the user (requires removing the driver PCB, changing current limiting resistors and resoldering LED wires)

The post NeoCree conversion module appeared first on Warsabers.

Belt clip

Warsabers — Mon, 20 Jan 2020 20:29:05 +0000

Star Wars Covertec Lightsaber Belt Clip The perfect addition to your Jedi or Sith Belt. The Covertec Belt Clip can be seen throughout the Prequel Trilogy. The clip attaches to your belt and holds your lightsaber hilt securely in place.

Covertec Lightsaber Clips fit most but not all Lightsabers.

The post Belt clip appeared first on Warsabers.

Soundboard Proffieboard v2.2

Warsabers — Mon, 20 Jan 2020 16:41:31 +0000

All-in-one STM32L4-based lightsaber electronics. It is small, feature-packed and 100% open source. This board retains all the features from the Teensy based designs, but are smaller and requires less work to put together. These are more advanced boards to use and it is recommended to read the detailed manual before use.

Listing includes 1 x Proffieboard v2.2 and 1 x 16GB Micro SD Card. As this is a new board, the full comprehensive manuals have yet to be written, however the board information and diagrams can be found here.

These boards have been improved since the v1.5 and now has:

Breadboard compatible, no more tiny soldering pads
Same size as before (1.3 x 0.7 inches)
BATT- and GND are bridged by default (the bridge can be cut if desired)
The components are a little farther away from the soldering pads
The SD card sticks out more than before, hopefully making it easier to grab.
FET pulldowns are grouned to BATT-, not GND
Reverse polarity protection
Beefier 5v power supply
Able to completely cut power to the SD card (this *should* make deep sleep possible)
The SD card power is also available on a pad, which could be used to cut power to bluetooth and displays during deep sleep.
Uses resistor arrays to cut down on the number of components
One less pad for neopixel data

It retains it’s legacy features:

Neopixel LED Strip and Tri Cree LED Support.
44/22/11khz Audio.
Touch Button Support.
Multiple Blades And Effects With Different Presets For Each.
Supports Both Monophonic and Polyphonic Sound Fonts
Can Play Background Music With Other Sounds.
Many Free Pins That Can Also Be Programmed For Other/Additional Features.
Supports SmoothSwing! The Most Realistic Motion Algorithm For Sabers To Date!

Technical info:

BATT+ – 2.6 to 4.5 volt input, drives everything except the LEDs
BATT- – negative pad for LEDs, needs to be at same level as GND when both are connected. Note that there are two of them, which can be useful when driving many powerful LEDs.
GND – ground for electronics except LEDs. Note that the two GND pads are interchangable and connected through the board.
Button 1/2/3 – Hook up to closing buttons, or potentially touch buttons.
Data 1 / ID – Normally used to measure the blade ID restor, and if it’s a neopixel blade, feed out neopixel data. For a fixed non-neopixel saber, it could be repurposed. Note that this pin has an internal 470 ohm resistor on it, so when hooked up to a neopixel blade, it does not need any resistors.
Data 2-3 – additional neopixel data outputs, or free for other purposes.
Data4/Dac – noeopixel data output, free, or audio DAC output
LED 1-6 – Hooks up to negative side of LED (positive side of LED hooks up directly to battery.) These pads can handle up to 30 volts.
SD Power – FET-controlled 3.3v. can be used to power down bluetooth and displays in low-power mode.
SDA, SCL – these pins are used to communicate with the gyro and accelerometer chip.
5v – generated by the proffieboard, normally it’s only on when sound is playing.
3.3v – generated by the proffieboard.
SWDIO, SWDCLK – can be hooked up to a ST-LINK device and lets you debug programs running on the proffieboard.

PLEASE NOTE: These boards will be fully tested and approved prior to shipping. It is highly recommended to have a professional saber builder install this board. If you wish to install yourself; it is at your own risk. WarSabers or Fredrik Hubinette cannot be held responsible for any damage to the board during installation. If there are any technical issues with the installation of the board please get in touch and we can forward you various information including groups and forums where troubleshooting can take place. These boards will have a 90-day warranty.

The post Soundboard Proffieboard v2.2 appeared first on Warsabers.

Blade plug

Warsabers — Mon, 20 Jan 2020 14:32:05 +0000

The post Blade plug appeared first on Warsabers.

Soundboard CerbeRUS NeoCore

Warsabers — Mon, 20 Jan 2020 13:32:52 +0000

Dimensions 50x22x5mm (1.98×0.87×0.2in) (Smaller than CerbeRUS Core by 20mm);
NeoPixel support (WS2812, WS2812B, WS2813 (RGB) with two Data channel. Max
Amperage 20A (recommended 4 pcs strips 1m length);
Full shutdown power supply from NeoPixel stripe in deep sleep mode. No need kill key;
Deep sleep mode with 0,0000007A Drain. No need kill key;
3 group of solder pads for easy wiring NeoPixel stripes;
Best sound MCU for 2W 4/8 ohm speakers. Max volume;
3 axis gyroscope + 3 axis accelerometer for perfect swing detection;
8 accent led pads;
2 button pads;
Micro USB port (extended or integrated) for charging and PC connection;
Battery protection from discharge and overcharge;
Protected from reverse battery connection;
Maximum power supply – 5V;
Additional pads for secondary charge port;
Micro SD for Sound fonts and settings;
3 preset Sound fonts;
Swing, Clash, Lockup, Stab, Blaster, Force, Combo, Spin, Flame blade effects;
NO NEED resistors to any led connections.

The post Soundboard CerbeRUS NeoCore appeared first on Warsabers.

Inquisitor hilt

Warsabers — Tue, 15 Oct 2019 14:21:31 +0000

Hilt:

Design – Warsabers, Russia;
The ability to combine two lightsabers into a staff using a special connector (selling separately);
Lenght: 299 mm;
OD: 36-40 мм.
Blade depth (aprox) – 56 mm/39 mm (PixelBlade/Tri-CREE);
Blade retention screw – M4, 1 pcs. Hex key included;
Сovertech wheel included. Covertech belt clip selling separately;
Hilt is designed for hard dueling.

The photo may differ slightly from the finished product, due to manual processing of the product and the peculiarities of color transfer by the camera and screen

Video reviews of various hilts

Electronics:

Warsabers CerbeRUS soundboard (Russia). Smoothswings + Accent swings algorithm support;
Pogo-Pin connector for PixelBlade RGB blade or for NeoCree Converter (Compatible with standard connectors from TCSS and similar);
Optional copper Converter Module with Tri-Cree RGB LED when Tri-Cree RGB is selected;
Removable battery 21700, 5000 mAh;
Micro-USB port on the hilt for charging and connecting to PC. Micro-USB cable included. Power adapter not included. (Adapter parameters: Output voltage – 5V, output current 0.5-1 A. Suitable for charging: PC, PS4, Xbox, Powerbank, telephone adapter with the necessary parameters);
Premium bass speaker D=28 mm, 2 W, 8 Om;

Video reviews of electronics and soundboards

Blade:

For PixelBlade RGB equipment: NeoPixel RGB blade (92 cm long, 3 mm wall thickness and a bullet tip). RGB LED strips are installed inside the blade along the entire length and allow you to customize any blade color;
For Tri-Cree equipment: standard empty blade (85 cm long, 2 mm wall thickness). Powerful Tre-Cree RGB LED are installed at the blade holder and allow you to customize any blade color.

The post Inquisitor hilt appeared first on Warsabers.

Kyle Katarn V3 hilt

Warsabers — Fri, 19 Jul 2019 13:50:27 +0000

The most accurate copy of the lightsaber Kyle Katarn – the main character of the game “Star Wars Jedi Knight”.

Hilt:

Design – Warsabers in coloboration with Maksim Tsvetkov, Russia;
Manufacturing – Warsabers, Russia;
Lenght: 320 mm;
OD: 38 мм;
Blade landing depth (aprox) – 35 mm;
Retention screw – M4, 1 pcs. Hex key included;
Hilt is designed for hard dueling.

Video reviews of various hilts

Electronics:

Soundboard Warsabers Cerberus (Russia) or Proffieboard* (USA). Smoothswings + Accent swings algorithm support;

*The price includes only basic firmware and a standard set of sound fonts from the official site of the soundboard developer. All other sounds, sound fonts and firmware are purchased separately and installed independently through the firmware of the board. Without updating firmware you can only replace pre installed sound fonts (not add new ones). Fonts can be replaced simply by your own by replacing files inside SD folders. Download Proffieboard datashet

ShtokCustomWorx Pogo-Pin connector with LEDs (Compatible with standard connectors from TCSS and similar);
Removable battery 18650, 3400 mAh.;
Micro-USB port on the hilt for charging and connecting to PC. Micro-USB cable included. Power adapter not included. (Adapter parameters: Output voltage – 5V, output current 0.5-1 A. Suitable for charging: PC, PS4, Xbox, Powerbank, telephone adapter with the necessary parameters);
Premium bass speaker D=28 mm, 2 W, 4 Om;

Video reviews of electronics and soundboards

The post Kyle Katarn V3 hilt appeared first on Warsabers.

Blade Scabbard

Warsabers — Sat, 22 Jun 2019 09:50:32 +0000

For blade D=25,4 мм.

The post Blade Scabbard appeared first on Warsabers.

Ben Solo hilt

Warsabers — Fri, 21 Jun 2019 14:48:10 +0000

Hilt size:

Length – 272 mm;
OD – 37-55 mm.

Dimensions for chassis space:

Length – 160 mm;
ID – 29,6 mm.

Equipment:

Empty hilt- 1 pcs;
Buttons – 2 pcs;

NOT included:

Heatsink module;
NeoPixel connector;
Belt clip;
Blade.

The post Ben Solo hilt appeared first on Warsabers.

Kyle Katarn V3 hilt

Warsabers — Mon, 29 Apr 2019 11:26:59 +0000

Hilt size:

Length - 320 mm.

Dimensions for chassis space:

Length - 220 mm;
ID - 22 mm.

Dimensions for aditional speaker space:

Length - 16 mm;
ID - 30 mm.

Dimensions for blade:

ID - 25,4 mm (1")

Equipment:

Empty hilt- 1 pcs;
Main black PCB with buttons - 1 pcs (see connection diagram);
Small Black PCB with pogo pins for "Speaker PCB" - 1 pcs
Speaker PCB - 1 pcs;
Brass pins - 1 set.

NOT included:

Battery contacts;
Switch TS01CQE;
Battery protection PCB TP4056PCM-YH10A-V1;
M2 self tapping screws;
Blade connector;
Soundboard;
Belt clip;
Blade.

The post Kyle Katarn V3 hilt appeared first on Warsabers.

Destiny hilt

Warsabers — Wed, 13 Feb 2019 17:57:26 +0000

Hilt:

Design – Warsabers, Russia;
Lenght: 295 mm;
OD: 28-38 mm;
Blade depth (aprox) – 70/55 mm (Neopixel/Tri-CREE);
Blade retention screw – M4, 1 pcs. Hex key included;
Leather not installed. Leather stripe is included for self-installation;
The ability to combine two lightsabers into a staff using a special connector (selling separately);
Сovertech wheel and belt clip selling separately;
Hilt is designed for hard dueling.

The photo may differ slightly from the finished product, due to manual processing of the product and the peculiarities of color transfer by the camera and screen

Video reviews of various hilts

Electronics:

Warsabers CerbeRUS soundboard (Russia). Smoothswings + Accent swings algorithm support;
Pogo-Pin connector for NeoPixel RGB blade or for NeoCree Converter (Compatible with standard connectors from TCSS and similar);
Optional Copper Converter Module with Tri-Cree RGB LED when Tri-Cree RGB is selected.
Removable battery 21700, 5000 mAh;
Micro-USB port on the hilt for charging and connecting to PC. Micro-USB cable included. Power adapter not included. (Adapter parameters: Output voltage – 5V, output current 0.5-1 A. Suitable for charging: PC, PS4, Xbox, Powerbank, telephone adapter with the necessary parameters);
Premium bass speaker D=28 mm, 2 W, 8 Om;

Video reviews of electronics and soundboards

Blade:

For NeoPixel RGB equipment: NeoPixel RGB blade (92 cm long, 3 mm wall thickness and a bullet tip). RGB LED strips are installed inside the blade along the entire length and allow you to customize any blade color;
For Tri-Cree equipment: standard empty blade (85 cm long, 2 mm wall thickness). Powerful Tre-Cree RGB LED are installed at the blade holder and allow you to customize any blade color.

The post Destiny hilt appeared first on Warsabers.

Starkiller hilt V4

Warsabers — Mon, 14 Jan 2019 09:33:04 +0000

The most accurate copy of Galen Marek (Starkiller) lightsaber – the main character of the the game “Star Wars: The Force Unleashed”.

Hilt:

Design – Warsabers, Russia;
Lenght: 285 mm;
OD: 38 мм;
Blade landing depth (aprox) – 44 mm/29 mm (Neopixel/Tri-CREE);
Blade retention screw – M4, 1 pcs. Hex key included;
Сovertech wheel included. Covertech belt clip selling separately;
Hilt is designed for hard dueling.
The color Weathered is made with a special burnishing compound, with active use it can be gradually wiped out to pure metal. It also has the ability to leave marks on hands when used with wet hands;

Video reviews of various hilts

The photo may differ slightly from the finished product, due to manual processing of the product and the peculiarities of color transfer by the camera and screen

Electronics:

Soundboard Warsabers Cerberus (Russia) or Proffieboard* (USA). Smoothswings + Accent swings algorithm support;

ShtokCustomWorx Pogo-Pin connector with LEDs (Compatible with standard connectors from TCSS and similar);
Removable battery 21700, 5000 mAh.;
Micro-USB port on the hilt for charging and connecting to PC. Micro-USB cable included. Power adapter not included. (Adapter parameters: Output voltage – 5V, output current 0.5-1 A. Suitable for charging: PC, PS4, Xbox, Powerbank, telephone adapter with the necessary parameters);
Premium bass speaker D=28 mm, 2 W, 4 Om;

Video reviews of electronics and soundboards

Blade:

For NeoPixel RGB equipment: NeoPixel RGB blade (92 cm long, 3 mm wall thickness and a bullet tip). RGB LED strips are installed inside the blade along the entire length and allow you to customize any blade color;
For Tri-Cree equipment: standard empty blade (85 cm long, 2 mm wall thickness). Powerful Tre-Cree RGB LED are installed at the blade holder and allow you to customize any blade color.

The post Starkiller hilt V4 appeared first on Warsabers.

Obi-Wan hilt

Warsabers — Fri, 28 Sep 2018 20:09:05 +0000

The post Obi-Wan hilt appeared first on Warsabers.

Qui-Gon hilt

Warsabers — Fri, 28 Sep 2018 19:33:50 +0000

The post Qui-Gon hilt appeared first on Warsabers.

Skywalker hilt

Warsabers — Mon, 27 Aug 2018 17:24:16 +0000

The post Skywalker hilt appeared first on Warsabers.

Revanted

Warsabers — Tue, 05 Dec 2017 19:00:26 +0000

Hilt:

Design and development – Warsabers & ShtokCustomWorx, Russia;
Lenght: 265 mm;
OD: 30-39 мм;
Blade landing depth (aprox) – 50 mm/35 mm (Neopixel/Tri-CREE);
Blade retention screw – M3, 1 pcs. Hex key included;
Сovertech wheel included. Covertech belt clip selling separately;
Hilt is designed for hard dueling.

The photo may differ slightly from the finished product, due to manual processing of the product and the peculiarities of color transfer by the camera and screen

Video reviews of various hilts

Electronics:

Soundboard Warsabers Cerberus (Russia);
Smoothswings + Accent swings algorithm support for NeoPixel RGB LED type;
Copper heatsink module for Tri-CREE LED type;
ShtokCustomWorx Pogo-Pin connector with LEDs for NeoPixel RGB LED type (Compatible with standard connectors from TCSS and similar);
Removable battery 21700, 5000 mAh.;
Micro-USB port on the hilt for charging and connecting to PC. Micro-USB cable included. Power adapter not included. (Adapter parameters: Output voltage – 5V, output current 0.5-1 A. Suitable for charging: PC, PS4, Xbox, Powerbank, telephone adapter with the necessary parameters);
Premium bass speaker D=28 mm, 2 W, 4 Om;

Video reviews of electronics and soundboards

Blade:

For NeoPixel RGB equipment: NeoPixel RGB blade (92 cm long, 3 mm wall thickness and a bullet tip). RGB LED strips are installed inside the blade along the entire length and allow you to customize any blade color;
For Tri-Cree equipment: standard empty blade (85 cm long, 2 mm wall thickness). Powerful Tre-Cree RGB LED are installed at the blade holder and allow you to customize any blade color.

The post Revanted appeared first on Warsabers.